Quantcast
Jump to content


Door Fabbing

Mopartist

By Mopartist
in Joyner UTV SxS Forum

 Share

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

brostar Proficient

brostar

Posted
Posted

That’s the old Team Joyner full enclosure with a hard roof including a front and rear window panel. Glad you replaced the ugly canvas side panels Rick. Great job, you get my thumbs up.

Cheers Mike.

ricksrb Mentor

ricksrb

Posted
Posted

Wow! Thats terrific!!! Great job! .....and suicide style! How did you end up latching and skinning them? Oh man! Is that a racing type gas filler cover?

thanks,

I made the latch out of 1/2" round stock with a spring and some 1/2" washers and cut a groove in the top rail of the door about 2" long.I picked up the fuel door cover at Kragens auto,40 bucks.

ricksrb Mentor

ricksrb

Posted
Posted

Rick,

Where did you get the top piece for your T4? Does it come with the front and rear windshields as well? Is it one piece?

I was also wondering where you got your front bumper from

I got it from a guy who purchased it at the joyner auction.It came with top,rear panel and window,front windsheild,canvas side panels,and top cargo carrier.Front bumper was purchased from joyner before they closed.

ricksrb Mentor

ricksrb

Posted
Posted

That’s the old Team Joyner full enclosure with a hard roof including a front and rear window panel. Glad you replaced the ugly canvas side panels Rick. Great job, you get my thumbs up.

Cheers Mike.

your right about the enclosure.

still have the ugly canvas side panels,Can still use them if I want.Once doors are open they lift off real easy and all my snaps and velcro are still there so the side panels can go on in minutes.

Guest Lenny

Guest Lenny

Posted
Posted

Nice job Ricksrb. Your probably right about a little more color. That should be easy to do, the hard thinking and work is done. I like that you can lift them off easily. Looks well thought out.

Lenny

ricksrb Mentor

ricksrb

Posted
Posted

Nice job Ricksrb. Your probably right about a little more color. That should be easy to do, the hard thinking and work is done. I like that you can lift them off easily. Looks well thought out.

Lenny

Thank you sir.

  • 3 weeks later...
ricksrb Mentor

ricksrb

Posted
Posted

Nice doors, can you post a photo or two of you snorkel set up? How does it seal up, assuming you can still lift the bed up.

Thanks,

Jeff

yes the bed still can be lifted up,below the bed is a 3" flex tubing that allows the bed to swing up.I do not recommend this set-up.I will be changing it because gets waaaay too much dust.

Kinarfi Veteran

Kinarfi

Posted
Posted

yes the bed still can be lifted up,below the bed is a 3" flex tubing that allows the bed to swing up.I do not recommend this set-up.I will be changing it because gets waaaay too much dust.

I like mine, flipped the intake, cut a cork gasket and drilled a few holes and it works good, as near as I know. Makes starter access easy, as well as the throttle butterfly.

2433032430104110397iuUiCU_th.jpg

ricksrb Mentor

ricksrb

Posted
Posted

Looks like you should be hauling people around at a Resort.

I had an idea like that.I thought of going down to the Tuson area and take people on tours of this ranch I heard about that has some wild steers running around on it that attack people(LOL)

Looks like he did what I was thinking of doing. Turn the chrome tube up off the engine.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • jamesxevan
      Hisun 500 Soft Cab Enclosure Upper Doors — Need Advice
      By jamesxevan
      I’ve been eyeing a Hisun 500 soft cab enclosure upper doors setup for my UTV, but I’m really not sure if it’s a smart move. The idea of doors and some protection sounds appealing, but I worry they might just be a flimsy afterthought — weak zippers, thin plastic windows, maybe leaking or fogging when wet or cold. What good is “protection” if it doesn’t seal well? Also concerned about ventilation: with soft doors, does the cab get too muggy or stuffy?
      Anyone here use soft-cab doors on a Hisun 500 — did they actually hold up for real riding conditions, or did you end up ditching them for hard doors (or no doors)?
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • Recon Marine
      BD300 won’t start or make any noise to try to start
      By Recon Marine
      Ran fine parked it in garage and 5 days later would not start or make any noise trying to start. Bought new battery, installed it and still nothing, no noise or anything. 
      Any idea? I can’t figure it out since when I parked it, it was running great. 
      Thanks
    • Recon Marine
      BD300 won’t start or make any noise to try
      By Recon Marine

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...