Quantcast
Jump to content


30" Tires on stock wheels


bruhaw

Recommended Posts

I know some of you have put 31" tires on and have had to do some fender well modifications. Wondering if I go to a 30"X10X14 on stock wheels if I will have to do any fender well mods up front. Hoping to be able to just use stock wheels mount the tires and have no issues with it rubbing on the well. I know 28" tires will be fine but hoping to maybe get that extra 1 inch of ride height with a 30". I have a T-4 so I high center at times.

Link to comment
Share on other sites

I have same tires on black ss wheels the front is good I think (have modded fenders) no rubing but you will break the back fenders if you bottom out. Take them off and move them up on top of horizontal pipe right above them and remount and they will be good

Link to comment
Share on other sites

2scoops has these tires. http://www.superatv....l-P963C709.aspx

They also offer a 28.5

My only warning is that these tires are much heavier than stock, but any 6 ply 30" ATV tire will be. I believe the 30x10x14 were 10lbs heavier a piece per tire than the stock, and the 30x12x14 were 15lbs heavier. That is a siginificant difference mainly due to the stock tires being made of paper mache and recycled road tar. By the time I changed them out the stock tires had more tire plugs and slime in them than air. I added Silverbullets fuel controller and it offset any powerloss and them some.

The benefits:

I can run them at low ATV pressures 5-10psi. This will impove your offroad ride alot. I think the stock tires call for around 30 psi???

I haven't had a flat yet (desert & mountain trail riding)

Traction is awesome in all areas.

The 30" size allows me to roll over much bigger rocks & bumps with ease. This helps me maintain my momentum which is a huge benefit with at stick shift.

The ground clearance with 30" tires is much better.

The price was good.

Most importantly--they look badass

The cons:

They don't balance worth a damn. I had a little steering wheel shimmy before I added the powersteering kit (now there is none).

They wear quickly, but that is inherent of an ATV tire. I think these may wear slightly quicker because the rubber is pretty soft. BUT this is why they stick to the rocks so well.

Off the line acceleration is a slightly slower, but top speed is higher.

Link to comment
Share on other sites

I went with the Vision 15" rims with 30 inch BF Goodrich tires. I just got back today from the Baja 250 and the tires made a big difference for me. Since I have the T-4 also the extra lift is great. I did also add a better fuel pump. I was flying over pieces of the course today having a blast. Now more suspension here I come.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Browner010
      Recently I had an overheating issue on my 2022 Coleman Outfitter 550 (Hisun UT550) and to check to make sure it was fixed I took it out for a ride around the block. After a couple cycles on the LED coolant meter, I took it for a couple mile ride and on my way back I heard a loud metallic snap then a grinding noise. It was still able to move under its own power but very slowly. I was about 2 blocks from the truck so 'I limped it home and up onto the trailer. I know I need to tear it apart and look for what broke, but anyone have a guess as to where to start? I'm seriously getting tired of this damn machine! 750 miles on it and already replaced the belt, wet clutch, primary clutch, clutch roller weights among a few other things. Seriously, this friggin machine has spent more time on the lift than on the road. I thought I bought this new because it was from the owner of a tractor supply, but he registered it under the stores name making me the 2nd owner voiding any and all warranties.
      Any Ideas what to look for would be appreciated.
      Thanks
    • By REDfletching
      Spent today at a Honda dealership looking at their 520 side by side, then on the way home past our Lowes noticed they had several new UTVs on site, so we U-turned and ducked in there. We were impressed that all that came for $9,999 metal whole length skid plate, nice sized bed, roof, windshield, side mirrors, winch, upgrade looking tires… all of which would have added thousands of dollars to an already expensive Honda 520. Now Honda does have a great reputation from my trusted UTV experienced buddy, so it has that going for it.
×
×
  • Create New...