Quantcast
Jump to content


2008 Can-Am commado only has front wheel drive

samrbeauchamp

By samrbeauchamp
in Can-Am BRP UTV SxS Forum

 Share

Recommended Posts

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet

It could be 2 things 1 the 4x4 switch 2 bad 4x4 actuator.With the ignition switch in the run position when you move the 4x4 switch you should hear a buzzing sound from the front differential switch.If you hear the buzz than the switch is ok.To check if the the actuator is to pull out the 4x4 actuator off. There is 1 screw on the driver side and 1 that you have to remove the tunnel by the shiftier to get to the other screw out.Once you have it out plug in the wiring and move the 4x4 switch take the cover off the actuator and see if the plastic screw moves than give me a call.928 344 2117

Thanks Frankie

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • paul allen
      2016 wildcat tail front axle rubber boot
      By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • Rmillerdesigns
      Massimo Msu 500 Has No Power
      By Rmillerdesigns
      Hello. I have a 2016 Massimo MSU 500. I was putting on a lightbar and i screwed up and didn't disconnect the battery so when i was taking of the positive cable to put on the power from the lightbar it sparked and now the utv has no power. I turn the key over and all i hear is a chirp. No lights or anything. Everything that comes from the battery to the jumper box up by the battery shows voltage but anything coming out does not such as to the winch or anything like that
    • dragon
      2016 Kubota 1100 RTV Tilt Steering wheel locked Upper Position
      By dragon
      I need help I have a 2016 Kubota 1100 RTV my tilt steering wheel locked in the upper position after using the side release. The handle works but does not release the steering wheel to a lower position. If anyone knows and easy fix, please let me know any help is appreciated. Be Safe, Thanks!
    • dragon
      2016 Kubota 1100 RTV Title Steering wheel locked
      By dragon
      Hi everyone, I am new to the site and I have one question. My tilt steering wheel is locked in the upper position, and I was hoping for someone could help me with the problem. I did spray some WD 40 in the area of the mechanism but still wheel is locked in the upper most position. I am willing to try anything to get the wheel free and move to a lower position. Any ideas will be appreciated. Thanks!! and Be Safe! 
    • Outlaw Redneck
      How to make a commando transmission work in sand spider
      By Outlaw Redneck
      Hello all. I have a 2005 Joyner sand spider 650 with the dreaded broken output shaft on the transmission. I got ahold of a 2007 joyner commando 650 for cheap that had a bad motor but a good transmission. I got it because everything i read said that the transmission would work but it seems that it will not. Due to the commando being 4x4 it has a selectable locker and a small ring gear using a "idler" gear to turn the ring gear which make the output spin the wrong direction. Is there any way that I can make this thing work? I really dont want a commando,  I like the buggy but if the trans wont work then I can only put my motor in the commando. Any help would be appreciated. I have the ring gear from the original trans but the shaft is broken and the shaft from the commando wont fit the ring gear it doesn't appear. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...