Quantcast
Jump to content


American SportWorks LM650 starting problems.

Mike Turner
 Share

Recommended Posts

Mike Turner Rookie

Mike Turner

Posted
Posted

American SportWorks LM 650 won’t start at times. Starter won’t engage the solenoid just “clicks” much like a weak battery would cause. Battery was replaced and problem went away and then came back. Replaced positive battery terminal. Problem resolved then returned. Replaced negative battery terminal. Problem gone then returned. Replaced the positive and negative battery cable ends. Problem resolved and now returned. The repair lasts for maybe 12 starts, then the solenoid just “clicks” again as it will with a weak battery. So I replaced the ignition switch. Problem solved for a week. With each “fix” the problem is resolved but only temporarily. Does anyone have any suggestions ? To replace the starter is expensive especially if it’s not the problem. 

Alex

Alex

Posted
Posted

Sounds like a bad starter. The starter will land on low spot. Try tapping the starter body with a small hammer and see if it cranks when you get the solenoid just clicking. If it starts, the starter needs to be replaced.

Travis Grand Master

Travis

Posted
Posted
1 hour ago, Alex said:

Sounds like a bad starter. The starter will land on low spot. Try tapping the starter body with a small hammer and see if it cranks when you get the solenoid just clicking. If it starts, the starter needs to be replaced.

Ditto

vaughn Enthusiast

vaughn

Posted
Posted

Make sure the starter is tight and the mounting points are clean. When it won't start pull the pull rope just enough to land on a different spot on the flywheel and then try to start with the starter. It could be a worn spot on the flywheel.

  • 1 month later...
  • 2 months later...
Mike Turner Rookie

Mike Turner

Posted
  • Author
Posted

@Travis Bad starter on an American LandMaster 650. “Finally “ found a starter. Subaru is out of the small engine business and replacement engine parts are scarce and expensive. Anyone ever  change a starter on an LM650? Can’t get on top mounting bolt. The service manual is no help and neither are shops in the area. Don’t want to just start removing hardware if it’s not necessary. 

Mike Turner Rookie

Mike Turner

Posted
  • Author
Posted

Installed the new starter on my LM650 with the Subaru engine. Removal was simple once the voltage regulator was removed. The starter would not engage all the time. Symptoms of a bad solenoid or bad starter. Subaru no longer is in the small engine business so locating a new started was difficult and expensive.  To my dismay, the new starter reacted the same. Here’s what I’ve done so far...replaced the ignition switch, the battery, the Battery cable ends, the battery post terminals, and now the starter with solenoid. I’ve cleaned or replaced any wire terminal dealing with the starter, ignition switch and battery. I have run out of ideas. The Subaru help line suggested the starter relay but that is part of the starter and the new starter covered that. The voltage regulator is the only thing not yet replaced but the dashboard digital volt meter indicates that it is working. Max voltage output is 14.25 volts and when the lights are turned on it drops to 12.5 volts. Does anyone have any suggestions ?

Mike Turner Rookie

Mike Turner

Posted
  • Author
Posted

Yes, it has a neutral safety switch. If the Vehicle is not in neutral, the ignition is completely dead. My problem is not That. The starter attempts to engage the flywheel but cannot. It seems like it cannot roll the engine over. After several attempts it will succeed and the motor starts. As I stated previously, additional amps were applied and the starter engaged each time. The battery is brand new and charged. 450CCA capacity. 

  • Like 1
vaughn Enthusiast

vaughn

Posted
Posted

When it won't start pull the pull rope just enough to land on a different spot on the flywheel and then try to start with the starter. It could be a worn spot on the flywheel.

  • 2 months later...
  • 4 months later...
  • 5 months later...
W B Enthusiast

W B

Posted
Posted

Old post but, I would have tried a valve adjustment. Controls  the decompression when starting allowing it t o turn over. Depending on where engine stops, it could be hard to turn over.

  • 5 months later...
FredTex Newbie

FredTex

Posted
Posted

I had the same problem with the starter clicking at times on my LM 700 with a Subaru engine. I contacted technical support at Subaru and they sent me a wiring diagram that had a relay switch being installed between the starter and solenoid. I took this with the relay to my UTV mechanic and he installed it and it totally fixed the problem. This was a defect with the this engine that they knew about. I think this is why Landmaster went to Briggs. .. Fred

  • Like 1
  • 8 months later...
  • 1 year later...
  • 3 weeks later...
W B Enthusiast

W B

Posted
Posted

ke the wires from the starter and move to the solenoids and run wire from solenoid to starter. Watch a mfew youtubes on installing a 12v solenoid and it should be clear. Don't get confused with re;ay. The solenoid becomes your relay. Chaep fix.

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • rdc
      Joyner 1100 oil pressure problem.
      By rdc
      I have a 2007 Joyner 1100 sand viper and  before it even get's to where the thermostat opens up the oil pressure get's so low I have to shut it down. What could fix this ? I thought about adding an oil cooler with fan, thicker oil, or removing the thermostat. Any advice?
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • jertex
      Shift cable problem, 2017 Stampede 900, need advice
      By jertex
      I bought a 2017 Stampede 900 last fall that was new, old stock with less than 5 hours on it thinking that I would be getting a relatively trouble free UTV as compared to buying a used Polaris or CanAm, or Honda, etc. It's been a little quirky, but reliable. What I thought was just a minor issue with this model, the difficulty in shifting between R, N, L, H, etc., was just a characteristic of this model is now a big problem. I had to climb two very steep trails to get to the upper meadow of our hunting property, which seemed to stress the UTV more than usual since I was carrying some lumber to work on a platform for a hunting blind, and when I went to shift into park, I felt something give and it would not shift out of low, but it did move up into high gear.  I couldn't get it to shift at all at that point and the shifter felt mushy for lack of a better word. I was able to get it down to the lodge and when I investigated, I discovered that the straight, metal tube portion of the shift cable had bent to almost 90 degrees (see pics). I'm positive that it had already had some deformation that had happened previously and it had the right amount of resistance to bend to the point where it was unusable. 
      I have two questions:
      1. I suspect that there must be some other issues that makes this UTV difficult to shift, and I'm wondering if this is a common problem and if someone could enlighten me on what could cause this to be difficult to shift?
      2. Have any of you had this happen and if so, how difficult is it to replace the shifter cable?
      Any other advice is welcome, this is the first UTV that I've ever owned, so I don't know much about working on these or maintaining them. I'm relatively capable when it comes to working on my own vehicles in general, and I'm not afraid to take things apart and get my hands dirty.
      Thanks in advance for any insight, I'll be traveling most the day so I won't get a chance to look at replies until this evening.


       
    • Hoppy one
      Bennche 500, replaced stator no fire
      By Hoppy one
      I replaced the stator on our Bennche 500 because it was not charging. It ran as long as you kept the battery charged. I replaced the stator now it’s not firing. The only problem I found was a wire in the new stator for the crank position sensor was in the wrong place in the plug. I switched it around but still no fire. Putting a meter on those wires and cranking the motor showed no voltage from the crank position sensor. Something I did or a bad “new “ part? Thanks for any ideas.
    • mfitzner
      No start
      By mfitzner
      Cranks after installing a jumper wire to ignition switch to get power but will not start
      Have spark and fuel pump runs
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...