Quantcast
Jump to content


Recommended Posts

Posted

I recently bought a 2010 Hisun 700 UTV and have been having a heck of a time with the throttle cable and carb.  I did get it to 38 miles an hour, but now its dropped to 33.  Is that the full speed for this buggy?  I am on my second throttle cable trying to find the correct length to make the speed consistent. I floor it, but it takes a good while to get up to speed.  What is everyone else getting for speed?  And any ideas on how to set the throttle cable or adjust the carb?  Thank you!! 

Posted

There has to be something wrong. I have had mine to 92kph ( 57mph) for a constant speed. Mind you that was with the stock clutch and I have put in a new one and haven't used it for a while to actually see what the top speed of it is now.  And that 92 kph was pretty quick to get too.  I would say something is wrong with yours.  When we pulled the stock chinese clutch, the plastic slides i think were all broke apart.

 

  • 1 month later...
Posted

Have your clutches serviced.

I had the same issue on a 2012 ys700 and found the primary and secondary clutches had never been serviced and were gummed up. clean them up and lube them per spec and you should be flying down the trail in no time.

  • 2 months later...
Posted

I have the exact same model and I can get it up to 75 - 80 kmh per hour so around 50 mph so something aint right on yours, clean all the jets or better yet just buy a new carb ($79) and try that, there are places with the right cables out there (https://www.vmcchineseparts.com/products/chinese-throttle-cable-95-hisun-500cc-700cc-version-75  this is $19.95) so try those 2 things

I have had mine since 2012, had carb replaced twice and ran amazing for 5 years each time so it is a good machine, just needs some love!!!

 

good luck

  • 5 months later...
Posted

seat belt fastened, but retarder applied. I have to find a way to cancel the speed breaker somehow. Actually, I had never worn both of them together. I was just wearing the driver's side. I will plug them in tomorrow and check for changes. Thank you

  • 8 months later...
Posted
On 1/20/2021 at 6:13 PM, ANIL SEDALI said:

 

Hello there. I have the same vehicle. There is a speed limit of 40 km. How did you cancel this limit?

I have the same problem with myUTV  Hisun 700 and the 40 km/h speed limiter.  How can i disconnect this, preferably with a switch. 

 
  • 7 months later...
  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By hetovi
      Hey everyone,
      I’m in the market for a UTV windshield that can withstand extreme conditions, including high winds, dust, and off-road impacts.
      I’ve seen a lot of options out there, but I’m unsure which one will provide the best protection and durability.
      Does anyone have experience with windshields that excel in these environments? Are there specific brands or materials you recommend?
      I’m particularly interested in options that offer both durability and clarity.
      Any tips or personal experiences would be greatly appreciated!
    • By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • By Chile
      2018 Massimo 700 MSU. The machine started burning oil all of a sudden. One day fine-- next morning burning oil. Looking for advice. Do I pull the engine to inspect the top end or can it be done with the engine in place? Pro? Cons?
      Any and all assistance is greatly appreciated in advance.
      Chile
       
    • By Chile
      2018 Massimo MSU 700 EFI. I realize that this engine is essential the same as in all of the HISUN based Yamaha clones out there. I am in the process of performing a top end diagnosis/rebuild. I have an AMAZON top end rebuild kit on order in anticipation of this activity. 
      Question 1:  When exploring the myriad of top end rebuild kits on the market for these units there are some cylinder assemblies that have "686 cm3" badging next to the cam cain tensioner boss. Others compatible with the unit do not have this badging. The existing cylinder assy does not have the 686 badging. I am assuming that this simply verifies that the cylinder assy is for a 686 cm3 engine which of course the stock 700 series HISUN engines are. Am I missing something here or is this just a manufacturer artifact? With or without the badging the application listings all indicate compatibility with the MSU 700 series engines.
      Question 2:  I have reviewed at minimum a dozen videos associated with this rebuild. To date I have not found one that deals with piston/cylinder clearance and/or ring gap verification. The advertised specifications for these various "top end rebuild kits" all indicate: Cylnider bore = 102mm and piston diameter=101.5mm. The math yields a .5mm (as in 1/2 mm) difference. That seems to be a very large piston/cylinder clearance.  I realize I am referencing advertised specs rather than emperically measured values but the numbers have gotten my attention.  I have referenced the FSM and found it to be somewhat confusing in this regard. Hopefully the experts on this forum can enlighten me as to where my observations are faulty here.
      Any and all assistance is greatly appreciated .
      Thank you all in advance,
      Chile
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
×
×
  • Create New...