Quantcast
Jump to content


First feedback

utvrally

By utvrally
in Member Feedback

 Share

Recommended Posts

utvrally Apprentice

utvrally

Posted
Posted

I'll be the first one to give you guys some feedback. I like to colors and the fact that it is light in here for the forum controls. Easy to navigate and loads fast. You will obviously just need some members. I'm sure they will come eventually. Simple to use, looking forward to the community. Good luck.

  • 1 year later...
brostar Proficient

brostar

Posted
Posted

I just joined and as I had a UTV that didn't have it's own section, I made a request and it was granted. Thanks (or as we say where I'm from, on yar mate)utv board, that shows us all you are pro-active.

Cheers Mike :):):)

Alex

Alex

Posted
Posted

Thank you all for the feedback! We will adjust this place as needed by the requets and feedback of our members. Spread the word, and welcome aboard to all of you that are new! I'm excited to see the participation!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • brewski
      installing light bar on kubota rtv 1100 x
      By brewski
      I just purchased a 2025 kubota rtv 1100 x cab esd esnting to install light bars on the roof it appears to be prewired for lights how do lights mount and what kind of switches do i need
    • KMP
      2015 Arctic Cat Wildcat Sport 700 XT (tips for maintenance / just purchase)
      By KMP
      We just bought our 1st side-by-side and wanted to get tips on maintenance items we should address immediately for our 2015 Arctic Cat Wildcat Sport 700 XT.  We are truly beginners and welcome any and all suggestions.  Thank you, we appreciate your help!
    • jon pino
      need resistance value on stator
      By jon pino
      having trouble with a 2013 uxv500i. have replaced stator due to bad pulser coil. new unit does not work. manual value for pulser coil is 100ish ohm, measured value is 500 ohm. can anyone with one of these fuel injected later model units check their pulser coil with an ohm meter for me? left side of engine small connector next to 3 yellows. jon 605-545-7040
    • jamesxevan
      Hisun 500 Soft Cab Enclosure Upper Doors — Need Advice
      By jamesxevan
      I’ve been eyeing a Hisun 500 soft cab enclosure upper doors setup for my UTV, but I’m really not sure if it’s a smart move. The idea of doors and some protection sounds appealing, but I worry they might just be a flimsy afterthought — weak zippers, thin plastic windows, maybe leaking or fogging when wet or cold. What good is “protection” if it doesn’t seal well? Also concerned about ventilation: with soft doors, does the cab get too muggy or stuffy?
      Anyone here use soft-cab doors on a Hisun 500 — did they actually hold up for real riding conditions, or did you end up ditching them for hard doors (or no doors)?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...