Quantcast
Jump to content


Textron Stampede leaking antifreeze

Greg Beachy
 Share

Recommended Posts

Greg Beachy Newbie

Greg Beachy

Posted
Posted

I have had a Bad Boy Stampede for almost two years now. I really like the machine but it seems like everytime I run it over 40 mph for more then a couple hundred yards it starts leaking antifreeze. The mechanic says it's a seal in the water pump, I've went through three water pumps now. Does anyone else have this problem?  And if so is there a fix for this? 

  • Alex changed the title to Textron Stampede leaking antifreeze
Greg Beachy Newbie

Greg Beachy

Posted
  • Author
Posted
13 hours ago, kenfain said:

After three pumps, I'd verify that the pumps are actually the problem. If so, then I'd look at the aftermarket pumps. What've you got to lose?

Ok thanks. What aftermarket pump did you go with? And how has performed for you?

 

kenfain Experienced

kenfain

Posted
Posted

At this point, any reputable aftermarket parts outlet should have what you need. Very few of them are actual OEM parts. As far as exactly which one, I don't really think it matters. As long as it's different from the one you've been using. A roll of the dice is as good as what you've been getting. The OEM one likely has some sort of casting flaw, causing it to defeat the seal integrity. Unless I'm misunderstanding the problem. 

When you're talking about water pump problems. There's really only the bearing, seal, and impeller. So when identifying your exact problem, you just give it a spin by hand. If it's a bearing problem, it'll feel gritty when turning it. If it turns smooth but leaks. Obviously it's only the replaceable seal. Seal kits are readily available for most of those models. Just make sure that it's a name brand pump, and preferably serviceable. 

Full disclosure; I don't own a Textron, I've had some experience in water pumps though.

  • 1 month later...
Rock-A-Buy Newbie

Rock-A-Buy

Posted
Posted

My Stampede started leaking at 1100 miles.  Required water pump *O* rings requiring pulled engine and $900 repair bill..  Nine hundred dry miles since.  Textron hasen't answerd  my letters about the problem.

cliffyk Rising Star

cliffyk

Posted
Posted
On 1/28/2021 at 9:45 PM, Greg Beachy said:

I have had a Bad Boy Stampede for almost two years now. I really like the machine but it seems like everytime I run it over 40 mph for more then a couple hundred yards it starts leaking antifreeze. The mechanic says it's a seal in the water pump, I've went through three water pumps now. Does anyone else have this problem?  And if so is there a fix for this? 

At the risk of sounding facetious, Find another mechanic!

 

  • 1 year later...
Stampede Newbie

Stampede

Posted
Posted

I have a 2019 Articat Stampede. The dealer replaced a leaky water pump at 400 miles. I have 900 miles on it now and it is leaking again.  My mechanic at the dealership said it’s a know problem. Any suggestions for a good fix would be appreciated 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • Jon W
      Havoc VS Stampede Motors
      By Jon W
      looking around and cannot find and Stampede motors, the Havoc looks to directly bolt in, with exception of the larger displacment. has anyone looked into this further? seems to be a better option considering stampede engines are on backorder. 
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • MilSurpYinzer
      Must have upgrades/spares?
      By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!
    • schreib69
      2008, 750 Teryx auction machine-- concerns!
      By schreib69
      I just bought an older (2008) Teryx 750 and am having some concerns.  Hoping of course, that most are not too big. . . but more knowledgeable folks like yourselves will surely have some ideas.  Thanks in advance.
      -- about 2700 hrs, camo version
      -- Starting:  after not running much at the auction site, I tried it and it was tough to start but half of this was likely I did not quite know the tricks for how long to keep the choke on. However, once it started it was kind of hard to keep running until it warmed up(once warmed it starts perfectly every time with no choke).  Now, back to running after the first ignition:  I had to hold the RPM's up a bit to keep it running and when doing so it sounded as if a little gnome was inside the engine pounding on something at random intervals.  Wondering if this could be detonation-- "knocking"?  After warming, it disappeared completely.  Maybe just need higher octane gas??
      -- After starting and running a bit there was a pretty terrible smell, most "like" burning rubber or an electrical fire.  No fire or resolution of this.  Eventually this TOO went mostly away, but still basically present.  Could it be adjustment needed for the main belt variable speed tranny?
      -- When I move from neutral into either Lo or HIGH range forward gears, I get gear clashing.  I did NOT put foot on brake and read in manual(just NOW) that you are supposed to do so.  (I have NOT gotten back out to check and see if this matters. )  OR, could it be part of the drive system is mashed up??!  Geez, hope not.
      -- There is a big open hole allowing direct sight into the belt transmission on the back right side.  This can't be normal, it must require some plastic cover.  Right?  Any rodent could get right into the transmission!
      -- THere appears to be no muffler or spark arrestor unit.  This "could " be the cause of some of the smell. . . ??  but that should not smell like burning rubber or electrical smell. . .
       
      SO.  That is all.  
      I sure would appreciate any insight on this issues and finally(!). . . if I was to take this into a local dealer what would you say are the top three issues I should have them address first?
       
      thanks!
    • Ironeagle
      2018 Massimo MSU 500. Cuts out at 18 MPH.
      By Ironeagle
      My 2018 Massimo MSU 500 was operating just fine.  I parked it for 2 weeks in my shop now the unit starts and runs great but at 18 MPH it cuts out. It's not the seatbelt safety switch that engages at 10 MPH if it is unbuckled. I purchased a new ECU but that did not resolve the problem. No error code is presented. I reset the ECU replaced the fuel injector, coil, sparkplug and spark plug wire. Same response. I don't mind replacing faulty components but don't want to chase parts and hope for the best. Any ideas??

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...