AXIS Off-Road UTV SxS Forum
This is for all of you AXIS Off-Road UTV, SxS (Side by Side) owners. Discussions about AXIS Off-Road specific topics including the Axis 500, 700, 750, and EV models.
29 topics in this forum
-
- 50 replies
- 57.5k views
-
- 4 replies
- 962 views
-
- 2 replies
- 217 views
-
- 4 replies
- 3.5k views
-
- 1 reply
- 295 views
-
- 0 replies
- 593 views
-
- 4 replies
- 591 views
-
- 2 replies
- 554 views
-
- 2 replies
- 1.1k views
-
- 0 replies
- 820 views
-
- 0 replies
- 698 views
-
- 2 replies
- 2k views
-
- 1 reply
- 1.2k views
-
- 6 replies
- 1.5k views
-
- 1 reply
- 1.5k views
-
- 0 replies
- 1.2k views
-
- 1 reply
- 1.6k views
-
- 18 replies
- 2.9k views
-
- 1 reply
- 1.7k views
-
- 4 replies
- 4k views
-
- 13 replies
- 5.3k views
-
- 1 reply
- 2.7k views
-
- 6 replies
- 2.3k views
-
- 12 replies
- 3.3k views
-
- 2 replies
- 3.3k views
-
- 2 replies
- 2.2k views
-
- 2 replies
- 3.6k views
-
- 9 replies
- 9.1k views
-
- 1 reply
- 4.3k views
.thumb.jpg.080f7ba3deabf170051987f7b5514b04.jpg)
-
Latest Posts
-
I'm having a similar issue with my Axis 500. It seems to bog down and struggle, particularly on inclines/hills (see video). Frustratingly, it also only happens intermittently, more often when the machine has been running for a while (I use it for farm work only). So far I have: Replaced fuel filter Replaced fuel injector Replaced MAP sensor (reset ECU after) Replaced spark plug Verified air filter is clean Verified no obstructions in exhaust I only run it on 91+ gas and put a can of seafoam through it to no avail I did previously have an issue with a failed one-way bearing, but this particular issue predates that failure. I replaced the one-way bearing a few months ago and inspected the wet clutch, primary/secondary clutches and belt while I was in there-didn't see anything of concern. Where do I go from here? IMG_9433.MOV -
By dave pasch · Posted
Got it running. The 4wd gets 12v power but does not engage. The posi traction (rear end) does not engage also. Any one have experience / ideas on fixing these items? Thanks Dave -
I don't know anything about the atvs, but he you tried shorting the solenoid with a screwdriver, and if so does it crank over or start? -
By Clyde says · Posted
Thanks for the info. I did locate the part on partstree and it was very expensive $291.00 plus tax and shipping total $325. The part wasn't much bigger than a quarter. I'll try and include a Pic. Anyway I installed it and the UTV runs well. Yes it is gas not propane. I switched to non-ethonal gas. -
Clyde, are you aware that number is for a propane carb. Are you trying to run it on gas? That carb is available for around 300.-00. If you were noty aware that it was propane powered, I would be trying to get a refundGood luckYou may be able to switch it to gas but thats not my forte. Oh, I saw the part available on partstree and a coupla other sites (ebay)
-
