Quantcast
Jump to content

silverbullet response

silverbullet

By silverbullet
in Joyner UTV SxS Forum

 Share

Recommended Posts

bruhaw Collaborator

bruhaw

Posted
Posted

The DB gauge is the one I went with and it works well. No issues at all except hooking it up can be a pain in the ass. Need to really look at the wires you are hooking up and where they go or don't go as the instructions suck and the customer service at Innovate out here in Irvine, CA sucks even worse. Guy is an a-hole at Innovate to say the least and he is their customer service. I ended up talking to the tech guy at Dobeck as they are very familiar with the Innovate air/fuel gauges and how they are set up. To get the Fuel programmer dialed in correctly I actually called the tech guy at Dobeck while out riding and dialed it in. Might have to adjust fuel pressure some and will have to play with the fuel controller some but he will walk you through it. You won't get 11HP but I did notice some increase and oddly enough sound difference as well once it was dialed in. Fuel economy will suffer as it does use the fuel. Without a gauge you just don't know what you are running and thus you almost have to go with a fuel/air gauge to make sure you are set.

Link to comment
Share on other sites
  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Quig
Quig

I have known Jose from when he was with SB, & know what he went thru,& still is dealing with somewhat.. I agree there have been some long delays,that should have been handled better. I know wh

plumber Proficient

plumber

Posted
Posted

Hey SB, Looks like your thread got hi-jacked again. Talking about someone else's product.....Maybe if you actually responded these would be your customers talking about your product. Instead since you still have not made any attempt to contact me and wont respond, I'll chime in here and let everyone know...

http://www.amazon.co...uel+ratio+gauge

Same A/F gauge SB sells, ships immediately, reputable seller, guaranteed to actually get your part, and its CHEAPER.

WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will now get my business.
Link to comment
Share on other sites
dedub Collaborator

dedub

Posted
Posted

WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will know get my business.

they got mine.i got my knew bearings thanks joyner usa. dedub
Link to comment
Share on other sites
nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted
WOW I can't believe this is not taken care of yet. I will not buy anything else from Jose no more until he takes care of this I ask all the people on here to help this man and not buy anything from Jose.This could be you next and you would want everybody to help you too.Lets send a message to Jose that this is WRONG. JOYNER USA will know get my business.

Agreed,

There's lot i want like the bush guard and headlight combo and other stuff i could probably drop 4-5k at sb but i refuse to buy anything more from sb until sb resolve the issue with merchant marnier

simple as that..... principles and customer service come first

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites
t2lizzard Contributor

t2lizzard

Posted
Posted

i just received my fuel controller and A/F gauge from SB this afternoon, under 15 days just as Jose promised. not sure what to make of all the SB bashing but i am a happy customer. i will say that although i am a happy customer, i wont be placing any more orders with SB until merchant mariner is looked after.

again, thanks for the parts Jose, i hope to install and be tire spinning by tomorrow afternoon.

Link to comment
Share on other sites
Merchant Mariner Enthusiast

Merchant Mariner

Posted
Posted

The DB gauge is the one I went with and it works well. No issues at all except hooking it up can be a pain in the ass. Need to really look at the wires you are hooking up and where they go or don't go as the instructions suck and the customer service at Innovate out here in Irvine, CA sucks even worse. Guy is an a-hole at Innovate to say the least and he is their customer service. I ended up talking to the tech guy at Dobeck as they are very familiar with the Innovate air/fuel gauges and how they are set up. To get the Fuel programmer dialed in correctly I actually called the tech guy at Dobeck while out riding and dialed it in. Might have to adjust fuel pressure some and will have to play with the fuel controller some but he will walk you through it. You won't get 11HP but I did notice some increase and oddly enough sound difference as well once it was dialed in. Fuel economy will suffer as it does use the fuel. Without a gauge you just don't know what you are running and thus you almost have to go with a fuel/air gauge to make sure you are set.

Wat kind of advice did the Dobeck tech give you on dialing in the fuel controller? Maybe he gave you some tips that could help me dial mine in a little better!

Link to comment
Share on other sites
charlie Experienced

charlie

Posted
Posted

Hey guys I have the fuel controller from sb I have had it for a whole now. I spoke with the tech department st ejk I believe it is the company that actually made the controller. I asked what should the set up be he told me if your running a snorkel and factory exhaust wich a lot of us are that to leave the programmer at the factory setting. He said with a wide band ad sensor precat converter and the post o2 disconnected you want 13.5 area at idle and low speeds 12.8 when you getting on it he said that will be best power for those mods and safest fuel economy will suffer lol. Just figured this would help also they recommended aem or innovations for the wide band af sensor

Link to comment
Share on other sites
nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted
Hey guys I have the fuel controller from sb I have had it for a whole now. I spoke with the tech department st ejk I believe it is the company that actually made the controller. I asked what should the set up be he told me if your running a snorkel and factory exhaust wich a lot of us are that to leave the programmer at the factory setting. He said with a wide band ad sensor precat converter and the post o2 disconnected you want 13.5 area at idle and low speeds 12.8 when you getting on it he said that will be best power for those mods and safest fuel economy will suffer lol. Just figured this would help also they recommended aem or innovations for the wide band af sensor

Hey Charlie,

Do your fuel controller have any vacuum Ports on controller itself?

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites
bruhaw Collaborator

bruhaw

Posted
Posted

No vacuum ports at all on the fuel controller. Best thing to do is call Dobeck Performance who makes the fuel controllers and they can help you dial it in. You may have to change your fuel pressure as well as I had to. If fuel pressure is too high then it affects the fuel controller. I had to turn down my fuel pressure to get the fuel controller to be able to do its job. If you call Dobeck just tell them you purchased a fuel controller through Silver Bullet and they will help you with it.

Link to comment
Share on other sites
nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted
nocturnalsixer

no vacume ports on my controller, yours does????

Charlie

Nope no fuel controller here yet I'm just asking because i heard about those..

No vacuum ports at all on the fuel controller. Best thing to do is call Dobeck Performance who makes the fuel controllers and they can help you dial it in. You may have to change your fuel pressure as well as I had to. If fuel pressure is too high then it affects the fuel controller. I had to turn down my fuel pressure to get the fuel controller to be able to do its job. If you call Dobeck just tell them you purchased a fuel controller through Silver Bullet and they will help you with it.

Bruhaw

I tried to get one through a member on forum but he didn't answer so i plan on calling dobeck myself and ask themabout that because i want a controller than can sense the turbo positive boost and negative vacuum like An secondary manifold absolute pressure sensor but for fuel controller

Sent from my DROID RAZR using Tapatalk 2

Link to comment
Share on other sites
dedub Collaborator

dedub

Posted
Posted

Charlie

Nope no fuel controller here yet I'm just asking because i heard about those..

Bruhaw

I tried to get one through a member on forum but he didn't answer so i plan on calling dobeck myself and ask themabout that because i want a controller than can sense the turbo positive boost and negative vacuum like An secondary manifold absolute pressure sensor but for fuel controller

Sent from my DROID RAZR using Tapatalk 2

i have one of them i'm sending to goindeep. doebec has ben makeing for.me. dedub
Link to comment
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Buddee
      2010 500 - New Carb- Hesitation
      By Buddee
      Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?
       
      Any help appreciated!
       
       
    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • Randyh79
      Hi new member, Randy from East Texas
      By Randyh79
      Just bought a Bad Boy Bandit 750. Need to change the oil and filter. Any suggestions would be greatly appreciated. I'm pretty sure this a Hisun 750 Sector even though it says it's a Bad Boy. I'll include pics soon.  
    • Xov
      New AMP Pro Owner
      By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • AndySwish33
      2023 T Boss 550 few questions
      By AndySwish33
      Brand new t boss 550. couple of questions. 
       
      1.  Do you need speakers in order to play music ?  Hooked my phone to Bluetooth no sound 
      2.  On screen registration.. it won’t let me fill in the info on the touch screen.  Navigation works but the registration portion does not 
      3.  Is there a data plan you can get or need ?  
       
      thanks everyone 


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...